Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 979
OK:
Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.
HINT
Radio frequencies may be interrupted due to surroundings or devices installed by the user.
NG -- CHECK IF ANY DEVICE IS INSTALLED BY USER
OK -- Continue to next step.
2. PERFORM INITIALIZATION
(a) Perform the initialization See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/Initialization (from 12/2010).
NOTICE:
Signals from a tire pressure warning valve and transmitter may be interrupted depending on the position of the valve. If
initialization is not completed, rotate the tire 90 to 270 degrees and perform initialization again.
NEXT -- Continue to next step.
3. READ VALUE USING TECHSTREAM (TIRE INFLATION PRESSURE)
(a) Make sure that the ignition switch is off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch on (IG).
(d) Turn the Techstream on.
(e) Check the values by referring to the table below. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Tire Pressure Monitor:
Showing posts with label HINT. Show all posts
Showing posts with label HINT. Show all posts
Tuesday, December 22, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 963
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 963
OK:
There are no momentary interruptions.
HINT
Perform the above inspection before removing the sensor and connector.
NG -- CHECK AND REPAIR HARNESS AND CONNECTOR (SPEED SENSOR CIRCUIT)
OK -- Continue to next step.
2. READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Select the Data List mode on the Techstream.
ABS/VSC/TRAC
(d) Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed
value displayed on the speedometer when driving the vehicle.
OK:
The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.
NG -- INSPECT FRONT SPEED SENSOR INSTALLATION
OK -- Continue to next step.
3. PERFORM TEST MODE (SIGNAL CHECK)
(a) Check if Test Mode DTCs are detected.
Result:
B -- INSPECT FRONT SPEED SENSOR INSTALLATION
A -- Continue to next step.
4. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS
(a) INSPECTION USING OSCILLOSCOPE
OK:
There are no momentary interruptions.
HINT
Perform the above inspection before removing the sensor and connector.
NG -- CHECK AND REPAIR HARNESS AND CONNECTOR (SPEED SENSOR CIRCUIT)
OK -- Continue to next step.
2. READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Select the Data List mode on the Techstream.
ABS/VSC/TRAC
(d) Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed
value displayed on the speedometer when driving the vehicle.
OK:
The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.
NG -- INSPECT FRONT SPEED SENSOR INSTALLATION
OK -- Continue to next step.
3. PERFORM TEST MODE (SIGNAL CHECK)
(a) Check if Test Mode DTCs are detected.
Result:
B -- INSPECT FRONT SPEED SENSOR INSTALLATION
A -- Continue to next step.
4. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS
(a) INSPECTION USING OSCILLOSCOPE
Sunday, December 20, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 924
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 924
(c) Check the test mode DTCs.
Result
HINT
DTCs C2181/81 to C2184/84 (Transmitter ID not Received) are output at this time, but they are not related to this check.
C -- GO TO DTC C2194/94 See: C Code Charts/C2194/Tire Pressure Monitoring (to 12/2010)
B -- GO TO DTC C2191/91 See: C Code Charts/C2191/Tire Pressure Monitoring (to 12/2010)
A -- USE SIMULATION METHOD TO CHECK See: Accessories and Optional Equipment/Antitheft and Alarm
Systems/Diagrams/Diagnostic Aids/How To Troubleshoot ECU Controlled Systems/How To Proceed With Troubleshooting
Vehicle Speed or Engine Speed Signal Malfunction - Tire Pressure Monitoring (from 12/2010)
TIRE AND WHEEL: TIRE PRESSURE WARNING SYSTEM: C2173/73: Vehicle Speed or Engine Speed Signal Malfunction
C2173/73 - Vehicle Speed or Engine Speed Signal Malfunction
DESCRIPTION
The tire pressure warning ECU receives a vehicle speed signal from the combination meter and an engine speed signal from the ECM. The tire
pressure warning ECU uses these signals to detect DTCs C2121/21 to C2125/25 (No Signal from Transmitter in Main Mode) and DTC C2177/77
(Initialization not Completed).
NOTICE:
When DTCs C2121/21 to C2125/25 are stored in the tire pressure warning ECU, DTC C2173/73 may be stored simultaneously. In
such cases, troubleshoot C2173/73 first, then troubleshoot DTCs C2121/21 to C2125/25 See: C Code Charts/C2121/Tire Pressure
Monitoring (from 12/2010).
(c) Check the test mode DTCs.
Result
HINT
DTCs C2181/81 to C2184/84 (Transmitter ID not Received) are output at this time, but they are not related to this check.
C -- GO TO DTC C2194/94 See: C Code Charts/C2194/Tire Pressure Monitoring (to 12/2010)
B -- GO TO DTC C2191/91 See: C Code Charts/C2191/Tire Pressure Monitoring (to 12/2010)
A -- USE SIMULATION METHOD TO CHECK See: Accessories and Optional Equipment/Antitheft and Alarm
Systems/Diagrams/Diagnostic Aids/How To Troubleshoot ECU Controlled Systems/How To Proceed With Troubleshooting
Vehicle Speed or Engine Speed Signal Malfunction - Tire Pressure Monitoring (from 12/2010)
TIRE AND WHEEL: TIRE PRESSURE WARNING SYSTEM: C2173/73: Vehicle Speed or Engine Speed Signal Malfunction
C2173/73 - Vehicle Speed or Engine Speed Signal Malfunction
DESCRIPTION
The tire pressure warning ECU receives a vehicle speed signal from the combination meter and an engine speed signal from the ECM. The tire
pressure warning ECU uses these signals to detect DTCs C2121/21 to C2125/25 (No Signal from Transmitter in Main Mode) and DTC C2177/77
(Initialization not Completed).
NOTICE:
When DTCs C2121/21 to C2125/25 are stored in the tire pressure warning ECU, DTC C2173/73 may be stored simultaneously. In
such cases, troubleshoot C2173/73 first, then troubleshoot DTCs C2121/21 to C2125/25 See: C Code Charts/C2121/Tire Pressure
Monitoring (from 12/2010).
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 919
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 919
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Diagnosis System (from 12/2010).
PROCEDURE
1. CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (DRIVER SIDE FRONT PRETENSIONER SQUIB)
(a) Turn the ignition switch off.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Diagnosis System (from 12/2010).
PROCEDURE
1. CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (DRIVER SIDE FRONT PRETENSIONER SQUIB)
(a) Turn the ignition switch off.
Tuesday, December 15, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 826
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 826
(a) Turn the ignition switch off.
(b) Record the output DTCs (for ABS, VSC system, and/or CAN communication system).
HINT
If CAN communication system DTCs and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor
DTCs (for ABS and/or VSC system) after the CAN communication system returns to normal.
NEXT -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control
Systems/Information Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
3. REPAIR OR REPLACE HARNESS OR CONNECTOR
(a) Turn the ignition switch off.
(b) Repair or replace the harness and connector.
(c) Check for any momentary interruption between the skid control ECU and each sensor or ECM See: Brakes and Traction
Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Check For
Intermittent Problems.
(d) Check that there is no momentary interruption.
NEXT -- Continue to next step.
4. RECONFIRM DTC
(a) Turn the ignition switch off.
(b) Clear the DTC See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
(c) Start the engine.
(d) Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.
(e) Check that no CAN communication system DTC is output See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Testing and Inspection/Reading and Clearing Diagnostic Trouble Codes.
(f) If ABS and VSC DTCs are output, record them.
Result:
HINT
The CAN communication system must be normal when performing troubleshooting for each sensor DTC (for ABS and/or VSC
system).
C -- END
B -- REPAIR CIRCUIT INDICATED BY OUTPUT CODE See: Diagnostic Trouble Code Descriptions/Vehicle Stability Control
System/Diagnostic Trouble Code Chart (from 12/2010)
A -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control Systems/Information
Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
Abnormal Temperature Inside ID1 Tire - Tire Pressure Monitoring (to 12/2010)
TIRE AND WHEEL: TIRE PRESSURE WARNING SYSTEM: C2165/65-C2169/69: Abnormal Temperature Inside ID1 Tire
C2169/69 - Abnormal Temperature Inside ID5 Tire
(a) Turn the ignition switch off.
(b) Record the output DTCs (for ABS, VSC system, and/or CAN communication system).
HINT
If CAN communication system DTCs and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor
DTCs (for ABS and/or VSC system) after the CAN communication system returns to normal.
NEXT -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control
Systems/Information Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
3. REPAIR OR REPLACE HARNESS OR CONNECTOR
(a) Turn the ignition switch off.
(b) Repair or replace the harness and connector.
(c) Check for any momentary interruption between the skid control ECU and each sensor or ECM See: Brakes and Traction
Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Check For
Intermittent Problems.
(d) Check that there is no momentary interruption.
NEXT -- Continue to next step.
4. RECONFIRM DTC
(a) Turn the ignition switch off.
(b) Clear the DTC See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
(c) Start the engine.
(d) Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.
(e) Check that no CAN communication system DTC is output See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Testing and Inspection/Reading and Clearing Diagnostic Trouble Codes.
(f) If ABS and VSC DTCs are output, record them.
Result:
HINT
The CAN communication system must be normal when performing troubleshooting for each sensor DTC (for ABS and/or VSC
system).
C -- END
B -- REPAIR CIRCUIT INDICATED BY OUTPUT CODE See: Diagnostic Trouble Code Descriptions/Vehicle Stability Control
System/Diagnostic Trouble Code Chart (from 12/2010)
A -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control Systems/Information
Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
Abnormal Temperature Inside ID1 Tire - Tire Pressure Monitoring (to 12/2010)
TIRE AND WHEEL: TIRE PRESSURE WARNING SYSTEM: C2165/65-C2169/69: Abnormal Temperature Inside ID1 Tire
C2169/69 - Abnormal Temperature Inside ID5 Tire
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 811
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 811
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Diagnosis System (from 12/2010).
PROCEDURE
1. CHECK DRIVER SIDE KNEE AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
(a) Turn the ignition switch off.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Diagnosis System (from 12/2010).
PROCEDURE
1. CHECK DRIVER SIDE KNEE AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
(a) Turn the ignition switch off.
Monday, December 14, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 801
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 801
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
63-52 - Clamp Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
63-52 - Clamp Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 800
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 800
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-44,62-48,62-50,63-44,63-48,63-50: CD Abnormal
63-50 - Tray Insertion / Ejection Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CLEAR DTC
(a) Clear the DTCs See: Accessories and Optional Equipment/Radio, Stereo, and Compact Disc/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
NEXT -- Continue to next step.
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
OK -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-44,62-48,62-50,63-44,63-48,63-50: CD Abnormal
63-50 - Tray Insertion / Ejection Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CLEAR DTC
(a) Clear the DTCs See: Accessories and Optional Equipment/Radio, Stereo, and Compact Disc/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
NEXT -- Continue to next step.
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
OK -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
Sunday, December 13, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 769
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 769
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
63-52 - Clamp Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
63-52 - Clamp Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CHECK RADIO RECEIVER ASSEMBLY
(a) Check if a disc can be changed, inserted or ejected normally.
OK:
Malfunction disappears.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 768
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 768
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-44,62-48,62-50,63-44,63-48,63-50: CD Abnormal
63-50 - Tray Insertion / Ejection Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CLEAR DTC
(a) Clear the DTCs See: Accessories and Optional Equipment/Radio, Stereo, and Compact Disc/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
NEXT -- Continue to next step.
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
OK -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-44,62-48,62-50,63-44,63-48,63-50: CD Abnormal
63-50 - Tray Insertion / Ejection Error
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CLEAR DTC
(a) Clear the DTCs See: Accessories and Optional Equipment/Radio, Stereo, and Compact Disc/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
NEXT -- Continue to next step.
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
OK -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-45,62-51,62-52,63-45,63-51,63-52: Eject Error
Saturday, December 12, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 746
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 746
(a) Turn the ignition switch off.
(b) Record the output DTCs (for ABS, VSC system, and/or CAN communication system).
HINT
If CAN communication system DTCs and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor
DTCs (for ABS and/or VSC system) after the CAN communication system returns to normal.
NEXT -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control
Systems/Information Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
3. REPAIR OR REPLACE HARNESS OR CONNECTOR
(a) Turn the ignition switch off.
(b) Repair or replace the harness and connector.
(c) Check for any momentary interruption between the skid control ECU and each sensor or ECM See: Brakes and Traction
Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Check For
Intermittent Problems.
(d) Check that there is no momentary interruption.
NEXT -- Continue to next step.
4. RECONFIRM DTC
(a) Turn the ignition switch off.
(b) Clear the DTC See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
(c) Start the engine.
(d) Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.
(e) Check that no CAN communication system DTC is output See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Testing and Inspection/Reading and Clearing Diagnostic Trouble Codes.
(f) If ABS and VSC DTCs are output, record them.
Result:
HINT
The CAN communication system must be normal when performing troubleshooting for each sensor DTC (for ABS and/or VSC
system).
C -- END
B -- REPAIR CIRCUIT INDICATED BY OUTPUT CODE See: Diagnostic Trouble Code Descriptions/Vehicle Stability Control
System/Diagnostic Trouble Code Chart (from 12/2010)
A -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control Systems/Information
Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-7D-62-7F,63-7D-63-7F: Disc cannot be Played
63-7F - Copyright Protection Error
(a) Turn the ignition switch off.
(b) Record the output DTCs (for ABS, VSC system, and/or CAN communication system).
HINT
If CAN communication system DTCs and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor
DTCs (for ABS and/or VSC system) after the CAN communication system returns to normal.
NEXT -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control
Systems/Information Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
3. REPAIR OR REPLACE HARNESS OR CONNECTOR
(a) Turn the ignition switch off.
(b) Repair or replace the harness and connector.
(c) Check for any momentary interruption between the skid control ECU and each sensor or ECM See: Brakes and Traction
Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Check For
Intermittent Problems.
(d) Check that there is no momentary interruption.
NEXT -- Continue to next step.
4. RECONFIRM DTC
(a) Turn the ignition switch off.
(b) Clear the DTC See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
(c) Start the engine.
(d) Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.
(e) Check that no CAN communication system DTC is output See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Testing and Inspection/Reading and Clearing Diagnostic Trouble Codes.
(f) If ABS and VSC DTCs are output, record them.
Result:
HINT
The CAN communication system must be normal when performing troubleshooting for each sensor DTC (for ABS and/or VSC
system).
C -- END
B -- REPAIR CIRCUIT INDICATED BY OUTPUT CODE See: Diagnostic Trouble Code Descriptions/Vehicle Stability Control
System/Diagnostic Trouble Code Chart (from 12/2010)
A -- INSPECT CAN COMMUNICATION SYSTEM See: Powertrain Management/Computers and Control Systems/Information
Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 62-7D-62-7F,63-7D-63-7F: Disc cannot be Played
63-7F - Copyright Protection Error
Friday, December 11, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 738
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 738
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 60-42-60-44,60-50: Tuner Power Source Error
60-50 - Malfunction in Internal IC
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CLEAR DTC
(a) Clear the DTCs See: Accessories and Optional Equipment/Radio, Stereo, and Compact Disc/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
NEXT -- Continue to next step.
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
OK -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 60-42-60-44,60-50: Tuner Power Source Error
60-50 - Malfunction in Internal IC
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010)
OK -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 60-42-60-44,60-50: Tuner Power Source Error
60-50 - Malfunction in Internal IC
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. CLEAR DTC
(a) Clear the DTCs See: Accessories and Optional Equipment/Radio, Stereo, and Compact Disc/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
NEXT -- Continue to next step.
2. RECHECK FOR DTC
(a) Recheck for DTCs and check if the same DTC is output again.
HINT
If DTCs are detected frequently, replace the radio receiver assembly.
OK:
No DTCs are output.
NG -- REPLACE RADIO RECEIVER ASSEMBLY See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010)
OK -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 60-42-60-44,60-50: Tuner Power Source Error
60-50 - Malfunction in Internal IC
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 728
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 728
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
PROCEDURE
1. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB)
(a) Turn the ignition switch off.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
PROCEDURE
1. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB)
(a) Turn the ignition switch off.
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 726
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 726
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. REPLACE RADIO RECEIVER ASSEMBLY
(a) Replace the radio receiver assembly See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010).
NEXT -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 57-10,57-47: TEL ECU Malfunction (TEL)
57-47 - Bluetooth Module Initialization Failed
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. REPLACE RADIO RECEIVER ASSEMBLY
(a) Replace the radio receiver assembly See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010).
NEXT -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 57-10,57-47: TEL ECU Malfunction (TEL)
57-47 - Bluetooth Module Initialization Failed
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. REPLACE RADIO RECEIVER ASSEMBLY
(a) Replace the radio receiver assembly See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (to 12/2010).
NEXT -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 57-10,57-47: TEL ECU Malfunction (TEL)
57-47 - Bluetooth Module Initialization Failed
DESCRIPTION
INSPECTION PROCEDURE
HINT
After the inspection is completed, clear the DTCs.
PROCEDURE
1. REPLACE RADIO RECEIVER ASSEMBLY
(a) Replace the radio receiver assembly See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Radio/Stereo/Service and Repair/Radio Receiver/Removal (from 12/2010).
NEXT -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 57-10,57-47: TEL ECU Malfunction (TEL)
57-47 - Bluetooth Module Initialization Failed
Thursday, December 10, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 722
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 722
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Diagnosis System (from 12/2010).
PROCEDURE
1. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (DRIVER SIDE CURTAIN SHIELD SQUIB)
(a) Turn the ignition switch off.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Diagnosis System (from 12/2010).
PROCEDURE
1. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (DRIVER SIDE CURTAIN SHIELD SQUIB)
(a) Turn the ignition switch off.
Tuesday, December 8, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 674
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 674
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
PROCEDURE
1. CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream See: Restraints and Safety
Systems/Air Bag Systems/Testing and Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag
system or driving the vehicle on a city or rough road See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Check Mode Procedure.
PROCEDURE
1. CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
Monday, December 7, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 645
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 645
* If any DTCs are output while jiggling a connector or wire harness of the ABS & TRACTION actuator assembly, inspect and
repair the connector or wire harness.
HINT
It is suspected that the DTCs were output due to a bad connection of the connector terminal.
B -- REPLACE ABS & TRACTION ACTUATOR ASSEMBLY
A -- END
Short in Driver Side Squib Circuit - Airbag System (to 12/2010)
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1800/51-B1803/51: Short in Driver Side Squib Circuit
B1803/51 - Short to B+ in Driver Side Squib Circuit
DESCRIPTION
* The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
* The circuit instructs the SRS to deploy when deployment conditions are met.
* These DTCs are recorded when a malfunction is detected in the driver side squib circuit.
* If any DTCs are output while jiggling a connector or wire harness of the ABS & TRACTION actuator assembly, inspect and
repair the connector or wire harness.
HINT
It is suspected that the DTCs were output due to a bad connection of the connector terminal.
B -- REPLACE ABS & TRACTION ACTUATOR ASSEMBLY
A -- END
Short in Driver Side Squib Circuit - Airbag System (to 12/2010)
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1800/51-B1803/51: Short in Driver Side Squib Circuit
B1803/51 - Short to B+ in Driver Side Squib Circuit
DESCRIPTION
* The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
* The circuit instructs the SRS to deploy when deployment conditions are met.
* These DTCs are recorded when a malfunction is detected in the driver side squib circuit.
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 641
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 641
OK:
There are no momentary interruptions.
HINT
Perform the above inspection before removing the sensor and connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM TO SKID CONTROL ECU)
OK -- Continue to next step.
2. CHECK DTC FOR ENGINE CONTROL SYSTEM
(a) Clear the DTC (engine control system).
(b) Check the DTC (engine control system).
Result:
B -- REPAIR ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT
A -- REPLACE ECM
3. REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM TO SKID CONTROL ECU)
NEXT -- Continue to next step.
4. RECONFIRM DTC
(a) Clear the DTC See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
(b) Perform a road test.
(c) Check that the same DTC is recorded See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and
Inspection/Reading and Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
Result:
B -- CHECK DTC FOR ENGINE CONTROL SYSTEM
A -- END
Open in Pump Motor Circuit - Vehicle Stability Control System (to 12/2010)
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: C1251/51: Open in Pump Motor Circuit
C1251/51 - Open in Pump Motor Circuit
DESCRIPTION
The pump motor is located inside the ABS & TRACTION actuator assembly.
OK:
There are no momentary interruptions.
HINT
Perform the above inspection before removing the sensor and connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM TO SKID CONTROL ECU)
OK -- Continue to next step.
2. CHECK DTC FOR ENGINE CONTROL SYSTEM
(a) Clear the DTC (engine control system).
(b) Check the DTC (engine control system).
Result:
B -- REPAIR ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT
A -- REPLACE ECM
3. REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM TO SKID CONTROL ECU)
NEXT -- Continue to next step.
4. RECONFIRM DTC
(a) Clear the DTC See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Reading and
Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
(b) Perform a road test.
(c) Check that the same DTC is recorded See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing and
Inspection/Reading and Clearing Diagnostic Trouble Codes/DTC Check / Clear (from 12/2010).
Result:
B -- CHECK DTC FOR ENGINE CONTROL SYSTEM
A -- END
Open in Pump Motor Circuit - Vehicle Stability Control System (to 12/2010)
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: C1251/51: Open in Pump Motor Circuit
C1251/51 - Open in Pump Motor Circuit
DESCRIPTION
The pump motor is located inside the ABS & TRACTION actuator assembly.
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 639
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 639
OK:
Waveform appears as shown in the illustration.
HINT
Waveform varies with the blower level.
Result:
B -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A -- REPLACE AIR CONDITIONING AMPLIFIER
Engine Control System Malfunction - Vehicle Stability Control System (to 12/2010)
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: C1201/51: Engine Control System Malfunction
C1201/51 - Engine Control System Malfunction
DESCRIPTION
If a malfunction in the engine control system is detected, the operations of VSC and TRAC are prohibited by the fail-safe function. When the signals
from the engine are input normally, the fail-safe is cancelled and the DTC is not stored.
INSPECTION PROCEDURE
PROCEDURE
1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
(a) Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to a DTC See: Brakes
and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Check For Intermittent Problems.
ABS/VSC/TRAC
OK:
There are no momentary interruptions.
HINT
Perform the above inspection before removing the sensor and connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM TO SKID CONTROL ECU)
OK -- Continue to next step.
OK:
Waveform appears as shown in the illustration.
HINT
Waveform varies with the blower level.
Result:
B -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A -- REPLACE AIR CONDITIONING AMPLIFIER
Engine Control System Malfunction - Vehicle Stability Control System (to 12/2010)
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: C1201/51: Engine Control System Malfunction
C1201/51 - Engine Control System Malfunction
DESCRIPTION
If a malfunction in the engine control system is detected, the operations of VSC and TRAC are prohibited by the fail-safe function. When the signals
from the engine are input normally, the fail-safe is cancelled and the DTC is not stored.
INSPECTION PROCEDURE
PROCEDURE
1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
(a) Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to a DTC See: Brakes
and Traction Control/Antilock Brakes / Traction Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Check For Intermittent Problems.
ABS/VSC/TRAC
OK:
There are no momentary interruptions.
HINT
Perform the above inspection before removing the sensor and connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM TO SKID CONTROL ECU)
OK -- Continue to next step.
Friday, November 27, 2020
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 43
Toyota Avalon V6-3.5L (2GR-FE) Manufacturer Code Page 43
PROCEDURE
1. CHECK "RADIO RECEIVER COMMUNICATION ERROR" IN PROBLEM SYMPTOMS TABLE
HINT
Refer to Radio Receiver Communication Error See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Testing and Inspection/Component Tests and General Diagnostics/Radio Receiver Communication Error (to 12/2010).
NEXT -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 01-D5,01-D8,01-D9,01-DA,01-DB,01-DE: Absence of Registration Unit
01-DE - Slave Reset
DESCRIPTION
HINT
* *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
* *2: If the power connector is disconnected after the engine starts, this DTC is stored after 180 seconds.
* *3: If the device is reported as not existing during verification, check the power source circuit and AVC-LAN circuit for the
device.
NOTICE:
* Before starting troubleshooting, be sure to clear the DTCs stored due to the reasons described in the HINT above. Then, check
for DTCs and troubleshoot according to the output DTCs.
* The radio receiver assembly is the master unit.
* Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.
INSPECTION PROCEDURE
NOTICE:
Be sure to read Description before performing the following procedure.
PROCEDURE
1. CHECK "RADIO RECEIVER COMMUNICATION ERROR" IN PROBLEM SYMPTOMS TABLE
HINT
Refer to Radio Receiver Communication Error See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Testing and Inspection/Component Tests and General Diagnostics/Radio Receiver Communication Error (from 12/2010).
NEXT -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 01-DC: Transmission Error
01-DC - Transmission Error
PROCEDURE
1. CHECK "RADIO RECEIVER COMMUNICATION ERROR" IN PROBLEM SYMPTOMS TABLE
HINT
Refer to Radio Receiver Communication Error See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Testing and Inspection/Component Tests and General Diagnostics/Radio Receiver Communication Error (to 12/2010).
NEXT -- END
Audio and Visual System (from 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 01-D5,01-D8,01-D9,01-DA,01-DB,01-DE: Absence of Registration Unit
01-DE - Slave Reset
DESCRIPTION
HINT
* *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
* *2: If the power connector is disconnected after the engine starts, this DTC is stored after 180 seconds.
* *3: If the device is reported as not existing during verification, check the power source circuit and AVC-LAN circuit for the
device.
NOTICE:
* Before starting troubleshooting, be sure to clear the DTCs stored due to the reasons described in the HINT above. Then, check
for DTCs and troubleshoot according to the output DTCs.
* The radio receiver assembly is the master unit.
* Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.
INSPECTION PROCEDURE
NOTICE:
Be sure to read Description before performing the following procedure.
PROCEDURE
1. CHECK "RADIO RECEIVER COMMUNICATION ERROR" IN PROBLEM SYMPTOMS TABLE
HINT
Refer to Radio Receiver Communication Error See: Accessories and Optional Equipment/Radio, Stereo, and Compact
Disc/Testing and Inspection/Component Tests and General Diagnostics/Radio Receiver Communication Error (from 12/2010).
NEXT -- END
Audio and Visual System (to 12/2010)
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: 01-DC: Transmission Error
01-DC - Transmission Error
Subscribe to:
Posts (Atom)